Image Acquisition	12-bit analog-to-digital converter Multiple cameras on the same 1394 bus automatically sync Faster standard frame rates, pixel binning and ROI Bulb-trigger mode, standard trigger mode Overlapped trigger input, image acquisition and transfer
Image Processing	On-camera control of gamma and LUT support Pixels contain frame-specific info (e.g. 1394 cycle time)
Camera and Device Control	Broadcast settings to all cameras on the same bus Fine-tune frame rates for video conversion (e.g. PAL, NTSC) Configurable strobe pattern output General purpose input/output pins for external device control Provides serial communication via GPIO digital logic levels Firmware upgradeable in field via IEEE-1394 interface.

---

*NOTE: One full KIT (get details) must be purchased prior to ordering individual cameras

Part Number	Description
SCOR-20SOM-CS	1600x1200 CCD B&W Scorpion Camera
SCOR-20SOC-CS	1600x1200 CCD Color Scorpion Camera
SCOR-14SOM-CS	1360x1024 CCD B&W Scorpion Camera
SCOR-14SOC-CS	1360x1024 CCD Color Scorpion Camera
SCOR-03SOM-CS	640x480 CCD B&W Scorpion Camera
SCOR-03KDM-CS	640x480 CMOS B&W Scorpion Camera
SCOR-03KDC-CS	640x480 CMOS Color Scorpion Camera
SCOR-13FFM-CS	1280x1024 CMOS B&W Scorpion Camera
SCOR-13FFC-CS	1280x1024 CMOS Color Scorpion Camera
SCOR-DEVKIT	Scorpion Development Accessory Kit
Download a list of available accessories for this model
NOTES: First time users are required to purchase a Development Accessory Kit in addition to purchasing the initial camera. Individual Scorpion cameras are not sold with optics.

---

• 4.5 meter, 6-pin, IEEE-1394 cable with ferrites
• IEEE-1394 OHCI PCI Host Adapter 3 port-400 Mbps card
• Tripod mounting adapter
• Hirose HR10 12-pin male GPIO connector prewired for easy triggering
• FlyCapture C/C++ SDK and device drivers

---

• Processor
  • Recommended – Intel Pentium^® 4 2.0 GHz or compatible processor
  • Minimum – Intel Pentium III 800 MHz or compatible processor
• Memory
  • Recommended – 512 MB RAM
  • Minimum - 256 MB RAM
• AGP video card with 64 MB video memory (128 MB recommended)
• 32-bit standard PCI slot for the IEEE-1394 card
• Supported operating system
• Microsoft Visual C++ 6.0 (to compile and run example code)

---

FCC / CE Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off or on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

RoHS / WEEE Compliance

This product is RoHS and WEEE compliant.

For additional information on RoHS and WEEE, click here.

---

Coming soon!